Bugs and Feature reqests

Support for EMU BLACK device
Post Reply
User avatar
Jadzwin
Site Admin
Posts: 1444
Joined: Tue Aug 12, 2014 11:27 pm

Bugs and Feature reqests

Post by Jadzwin » Sat Nov 19, 2016 1:48 pm

Hi there!

You can submit here founded bugs and feature requests for EMU software.

Thanks to your support our products will get better and better.

It is for you guys!


Ecumaster Team

No Limits
Posts: 17
Joined: Thu Nov 13, 2014 4:31 pm

Re: Bugs and Feature reqests

Post by No Limits » Sun Nov 20, 2016 1:03 pm

under tools "show assigned inputs" missing CAN INPUTS and the order is wrong
inputs.jpg
under BOOST BOOST/BLEND SWITCH input missing CAN ANALOG

On the Android Tablet CLT always 0. Analog input1 tells correct value, analog input1 as olpressure tells 0.
testet with Emu Black and DL1

User avatar
Jadzwin
Site Admin
Posts: 1444
Joined: Tue Aug 12, 2014 11:27 pm

Re: Bugs and Feature reqests

Post by Jadzwin » Sun Nov 20, 2016 2:33 pm

Already fixed, new version will be available in next few days

magelius
Posts: 36
Joined: Mon Oct 12, 2015 9:41 am

Re: Bugs and Feature reqests

Post by magelius » Wed Nov 23, 2016 4:41 pm

When starting the software, it gives always this error message. Problem in PC or SW?
Setup: HP Zbook 15 G3, Win 7 Enterprise, Service Pack 1
Message: Can't Load 'ftd2xx.dll'
Attachments
error.png

magelius
Posts: 36
Joined: Mon Oct 12, 2015 9:41 am

Re: Bugs and Feature reqests

Post by magelius » Wed Nov 23, 2016 4:44 pm

The column width is too narrow and it can't be changed. All the text information are not visible.
Attachments
column_width.png

magelius
Posts: 36
Joined: Mon Oct 12, 2015 9:41 am

Re: Bugs and Feature reqests

Post by magelius » Wed Nov 23, 2016 4:49 pm

It would be nice to have additional feature/value input for Flat shit. There is only "ignition retard value" for flat shifting (clutch switch activated).
Is it possible to add "absolute ignition value" instead of retard, or best case is to let user choose is it absolute value or retarding value.
Attachments
absolute_ignition.png

User avatar
Jadzwin
Site Admin
Posts: 1444
Joined: Tue Aug 12, 2014 11:27 pm

Re: Bugs and Feature reqests

Post by Jadzwin » Thu Nov 24, 2016 5:39 pm

It is doable. I add it to to do list.

Did you get rid of the ftdi.dll message ? It means that you have no drivers installed.

magelius
Posts: 36
Joined: Mon Oct 12, 2015 9:41 am

Re: Bugs and Feature reqests

Post by magelius » Fri Nov 25, 2016 9:15 am

Thanks for adding to do list! The .dll problem is still there. I have installed "CDM21224_Setup.exe" also, didn't help.

Some feature suggestions:
- I know that the actual lambda value is the only right physical quantity for fuel tuning, and the AFR is just calculated value based on lambda and fuel type. But for me (maybe someone else also) it is a lot easier and better to read and tune the AFR values, maybe because I am used to it. So, is it possible to add feature that user can choose the fuel target table based on lambda values or based on AFR values? And if AFR values are used, then we need for instance some calibration graph or just equation input, that this lambda is for this AFR value. Of course, then the lambda target gauge should follow the option lambda or AFR.

- Can you add text gauge option for the gauges? It is very useful if user can add several numerical values and make a kind of numerical value list. Like this way:
AFR 14.7
Igniton Advance 25 deg
MAP 200 kPa
....and so on

- I think it would be very visual and efficient that user can add warning lights and limits, e.g. just mouse right click on the gauge "add warning light", then "max limit" and "min limit". The warning could maybe flash the gauge to red color or just extra light next to the gauge. There are several things that tuner must follow during tuning/pull. Often if tuning on highway, it is hard to see everything on the screen and debug problems. Well, we have log and there we can see everything and of course this is the most accurate way. But many times you just want to quick see what happens after changes. Just simple example:
User are tuning wastegate duty-cycle or adjusting the closed loop parameters. Your target MAP is 200kPa and warning is min: 195kPa and max: 205kPa. You are tuning it alone at highway and your laptop is somewhere near. You can immediately see from the screen that the light flashes -> then adjust parameters and next try.. so on.

User avatar
Jadzwin
Site Admin
Posts: 1444
Joined: Tue Aug 12, 2014 11:27 pm

Re: Bugs and Feature reqests

Post by Jadzwin » Tue Nov 29, 2016 5:45 pm

The mechanism for warnig is alread preset.
On the picture below the CLT alarm is enabled and on the toolbard the CLT warning is blinking.

Image

User avatar
GearTech_Greece
Posts: 47
Joined: Thu Jun 04, 2015 12:26 am

Re: Bugs and Feature reqests

Post by GearTech_Greece » Mon Dec 05, 2016 10:53 am

Some features:

Idle valve DC vs IAT correction
Warmup enrichment table -> 3D (4D RPM and LOAD would be perfect but LOAD alone (3D) is just fine. Engines need much more enrichment in low RPM and high loads)
S2k trigger improvement to add second cam for faster engine start

It's impressive I can't really think anything else for 99% of customers' cars. Good work guys!

Zeke21
Posts: 1
Joined: Mon Dec 05, 2016 10:39 am

Re: Bugs and Feature reqests

Post by Zeke21 » Mon Dec 05, 2016 4:24 pm

TC and DBW not visible in PC Client tree-view. I have 2.019 version.
What is missing. Is it a must to connect to EMU-device (firmware)?

BR/Johan

samvel
Posts: 256
Joined: Fri Aug 15, 2014 9:44 pm
Location: Tallinn, Estonia
Contact:

Re: Bugs and Feature reqests

Post by samvel » Mon Dec 05, 2016 11:16 pm

Zeke21 wrote:TC and DBW not visible in PC Client tree-view. I have 2.019 version.
What is missing. Is it a must to connect to EMU-device (firmware)?

BR/Johan
Tools > Available strategies
www.esracing.ee / www.facebook.com/esracingestonia

No Limits
Posts: 17
Joined: Thu Nov 13, 2014 4:31 pm

Re: Bugs and Feature reqests

Post by No Limits » Sat Dec 10, 2016 8:27 am

Please check the datastream to Datalogger, there are something wrong.
On the Android Tablet CLT always 0. Analog input1 tells correct value, analog input1 as olpressure tells 0.
testet with Emu Black and DL1

User avatar
Jadzwin
Site Admin
Posts: 1444
Joined: Tue Aug 12, 2014 11:27 pm

Re: Bugs and Feature reqests

Post by Jadzwin » Sat Dec 10, 2016 1:16 pm

You need to upgrade data loger software. We will publish it on Monday.

User avatar
Jadzwin
Site Admin
Posts: 1444
Joined: Tue Aug 12, 2014 11:27 pm

Re: Bugs and Feature reqests

Post by Jadzwin » Mon Dec 12, 2016 3:36 pm

New datalogger firmware available on our webpage:

http://www.ecumaster.com/products/data-logger-dl-1/

magelius
Posts: 36
Joined: Mon Oct 12, 2015 9:41 am

Re: Bugs and Feature reqests

Post by magelius » Fri Dec 30, 2016 9:36 am

Is it possible to add feature to BMW e46 CAN?
Original fuel consumption meter can be used for boost level. It is 0-20L/km, so it could be e.g. 0-2bar.
How about using the average fuel consumption digital value for showing real time AFR?

yehiel
Posts: 2
Joined: Sat Dec 31, 2016 7:44 am

Re: Bugs and Feature reqests

Post by yehiel » Sat Dec 31, 2016 12:42 pm

hi

I have the same dll problem!
way is that?

and also I see all letters in gibberish and not English,

any help

User avatar
Jadzwin
Site Admin
Posts: 1444
Joined: Tue Aug 12, 2014 11:27 pm

Re: Bugs and Feature reqests

Post by Jadzwin » Thu Jan 05, 2017 11:10 pm

Please download latest software here:

http://www.ecumaster.com/black

And be sure you have USB driver installed:

http://www.ftdichip.com/Drivers/CDM/CDM21224_Setup.zip

nickbmw
Posts: 134
Joined: Sat Mar 26, 2016 11:23 pm

Re: Bugs and Feature reqests

Post by nickbmw » Mon Jan 09, 2017 12:20 am

Can you allow the tps % settings one decimal digit resolution?

User avatar
Jadzwin
Site Admin
Posts: 1444
Joined: Tue Aug 12, 2014 11:27 pm

Re: Bugs and Feature reqests

Post by Jadzwin » Mon Jan 09, 2017 8:32 pm

Actually resolution 0.5 for VE and Ignition table is available.

Post Reply
stół kuchenny okrągły

Who is online

Users browsing this forum: No registered users and 3 guests